Vehicle wraps & decals: The two techniques mentioned above will remove the majority of hail damage on your car, but a professional job at your local auto body shop is recommended for deep dents or badly damaged surfaces. The services tend to be cheap, fast and rarely require a new paint job. However, it is a good idea to compare prices and offered services at various body shops to see which package works best for your wallet and car’s situation.

In the first place let’s start with some car paint care recommendations: Another way to fix the small dents is parking your car in a sunny area. This is an effective way that most of car enthusiasts all know. By doing this way, the metal will heat up and expand. As the car surface expands, the shallow and light dents will pop out. The longer you park your car in a sunny area, the more likely this way will work.

Don’t underestimate the necessary step of decontamination prior to application of your chosen wax. If you fail to do this step, you will get disappointing results regardless of the type of wax you have chosen. And yes…even that brand new car straight off the dealer lot will in have some form of pollutants already on the car paint from its travel from the factory to the car dealership. Clear coat is the top layer of your cars paint. It acts as a protective layer to filter out UV rays. But your clear coat is what you are trying to take care of with the above requirements. People get confused about clear coat vs. car paint. Virtually every car today is finished with a clear coat as the top layer. Think of it as car paint with no color added to it.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.

In order to protect new car paint, you have to invest some time and effort to clean the vehicle on a regular basis. There are several car waxes and polishes available on the market. Although some car product manufacturers claim their products produce long lasting results, you will have to re-apply any product every few months, so the exteriors look appealing. If you’ve purchased a new vehicle that has a shiny coat of factory paint, avoid using too many detailing products as they rob the car of its original luster and also damage the paint. Read additional info on Paint Protection Film Colorado Springs.

Throughout the 1990s, automotive paints and vehicle body materials were high quality and much more resilient to bending. Since both the paint and the body could be bent without significant damage to the paint or permanent damage to the body materials, an entire industry formed based around the concept and technology of repairing dents.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.